update
¶
Description¶
Updates the specified tunnel. This operation lets you change tunnel attributes such as the routing type (BGP dynamic routing or static routing). Here are some important notes:
If you change the tunnel’s routing type or BGP session configuration, the tunnel will go down while it’s reprovisioned.
If you want to switch the tunnel’s routing from STATIC to BGP, make sure the tunnel’s BGP session configuration attributes have been set (bgpSessionConfig).
If you want to switch the tunnel’s routing from BGP to STATIC, make sure the IPSecConnection already has at least one valid CIDR static route.
Required Parameters¶
-
--ipsc-id
[text]
¶
The OCID of the IPSec connection.
-
--tunnel-id
[text]
¶
The OCID of the tunnel.
Optional Parameters¶
-
--bgp-session-config
[complex type]
¶
This is a complex type whose value must be valid JSON. The value can be provided as a string on the command line or passed in as a file using the file://path/to/file syntax.
The --generate-param-json-input
option can be used to generate an example of the JSON which must be provided. We recommend storing this example
in a file, modifying it as needed and then passing it back in via the file:// syntax.
-
--display-name
[text]
¶
A user-friendly name. Does not have to be unique, and it’s changeable. Avoid entering confidential information.
-
--dpd-config
[complex type]
¶
This is a complex type whose value must be valid JSON. The value can be provided as a string on the command line or passed in as a file using the file://path/to/file syntax.
The --generate-param-json-input
option can be used to generate an example of the JSON which must be provided. We recommend storing this example
in a file, modifying it as needed and then passing it back in via the file:// syntax.
-
--encryption-domain-config
[complex type]
¶
This is a complex type whose value must be valid JSON. The value can be provided as a string on the command line or passed in as a file using the file://path/to/file syntax.
The --generate-param-json-input
option can be used to generate an example of the JSON which must be provided. We recommend storing this example
in a file, modifying it as needed and then passing it back in via the file:// syntax.
-
--force
¶
Perform update without prompting for confirmation.
-
--from-json
[text]
¶
Provide input to this command as a JSON document from a file using the file://path-to/file syntax.
The --generate-full-command-json-input
option can be used to generate a sample json file to be used with this command option. The key names are pre-populated and match the command option names (converted to camelCase format, e.g. compartment-id –> compartmentId), while the values of the keys need to be populated by the user before using the sample file as an input to this command. For any command option that accepts multiple values, the value of the key can be a JSON array.
Options can still be provided on the command line. If an option exists in both the JSON document and the command line then the command line specified value will be used.
For examples on usage of this option, please see our “using CLI with advanced JSON options” link: https://docs.cloud.oracle.com/iaas/Content/API/SDKDocs/cliusing.htm#AdvancedJSONOptions
-
--if-match
[text]
¶
For optimistic concurrency control. In the PUT or DELETE call for a resource, set the if-match parameter to the value of the etag from a previous GET or POST response for that resource. The resource will be updated or deleted only if the etag you provide matches the resource’s current etag value.
-
--ike-version
[text]
¶
Internet Key Exchange protocol version.
Accepted values are:
V1, V2
-
--max-wait-seconds
[integer]
¶
The maximum time to wait for the resource to reach the lifecycle state defined by --wait-for-state
. Defaults to 1200 seconds.
-
--nat-translation-enabled
[text]
¶
By default (the AUTO setting), IKE sends packets with a source and destination port set to 500, and when it detects that the port used to forward packets has changed (most likely because a NAT device is between the CPE device and the Oracle VPN headend) it will try to negotiate the use of NAT-T.
The ENABLED option sets the IKE protocol to use port 4500 instead of 500 and forces encapsulating traffic with the ESP protocol inside UDP packets.
The DISABLED option directs IKE to completely refuse to negotiate NAT-T even if it senses there may be a NAT device in use.
Accepted values are:
AUTO, DISABLED, ENABLED
-
--oracle-initiation
[text]
¶
Indicates whether the Oracle end of the IPSec connection is able to initiate starting up the IPSec tunnel.
Accepted values are:
INITIATOR_OR_RESPONDER, RESPONDER_ONLY
-
--phase-one-config
[complex type]
¶
This is a complex type whose value must be valid JSON. The value can be provided as a string on the command line or passed in as a file using the file://path/to/file syntax.
The --generate-param-json-input
option can be used to generate an example of the JSON which must be provided. We recommend storing this example
in a file, modifying it as needed and then passing it back in via the file:// syntax.
-
--phase-two-config
[complex type]
¶
This is a complex type whose value must be valid JSON. The value can be provided as a string on the command line or passed in as a file using the file://path/to/file syntax.
The --generate-param-json-input
option can be used to generate an example of the JSON which must be provided. We recommend storing this example
in a file, modifying it as needed and then passing it back in via the file:// syntax.
-
--routing
[text]
¶
The type of routing to use for this tunnel (BGP dynamic routing, static routing, or policy-based routing).
Accepted values are:
BGP, POLICY, STATIC
-
--wait-for-state
[text]
¶
This operation creates, modifies or deletes a resource that has a defined lifecycle state. Specify this option to perform the action and then wait until the resource reaches a given lifecycle state. Multiple states can be specified, returning on the first state. For example, --wait-for-state
SUCCEEDED --wait-for-state
FAILED would return on whichever lifecycle state is reached first. If timeout is reached, a return code of 2 is returned. For any other error, a return code of 1 is returned.
Accepted values are:
AVAILABLE, PROVISIONING, TERMINATED, TERMINATING
-
--wait-interval-seconds
[integer]
¶
Check every --wait-interval-seconds
to see whether the resource has reached the lifecycle state defined by --wait-for-state
. Defaults to 30 seconds.
Global Parameters¶
Use oci --help
for help on global parameters.
--auth-purpose
, --auth
, --cert-bundle
, --cli-auto-prompt
, --cli-rc-file
, --config-file
, --connection-timeout
, --debug
, --defaults-file
, --endpoint
, --generate-full-command-json-input
, --generate-param-json-input
, --help
, --latest-version
, --max-retries
, --no-retry
, --opc-client-request-id
, --opc-request-id
, --output
, --profile
, --proxy
, --query
, --raw-output
, --read-timeout
, --realm-specific-endpoint
, --region
, --release-info
, --request-id
, --version
, -?
, -d
, -h
, -i
, -v